Hotline
+86-519-88678001 +86-519-88908008Working principle
SZG double cone rotary vacuum dryer for double cone rotary tank, the tank in the vacuum state, into the jacket into the heat conduction oil or hot water to heat, heat through the tank wall and wet material contact. Water vapor or other gases evaporated after the wet material is endothermic and pumped through the vacuum exhaust pipe. As the tank in the vacuum state, and the rotation of the tank to keep the material constantly up and down, inside and outside, so that speed up the drying speed of the material, improve the drying rate, to achieve uniform drying purposes.
Features
Double cone rotary Vacuum dryer is a new type of dryer which integrates mixed-drying in one. The condenser, vacuum pump and dryer are matched to form a vacuum drying device. (If you do not need to recycle solvents, condensers can not be used) The machine advanced design, internal structure is simple, easy to clean, material can be all discharged, easy to operate. Can reduce labor intensity and improve working environment. At the same time because the container itself rotation material also rotates, but the wall does not accumulate material, the heat transfer coefficient is high, drying rate is large, not only saves energy, and the material is dry evenly, good quality. Can be widely used in pharmaceutical, chemical, food, dyes and other industries dry.
Application range
This machine is suitable for the vacuum drying and mixing of powder and granular materials in medicine, food, chemical industry and so on, especially for drying by
The following requirements: ※ cannot accept heat-
sensitive materials of high temperature ※ materials
for recovering solvents and poisonous gases ※ easy to oxidize ,
Hazardous materials ※ Materials required for
crystallization ※ Material
Specifications with very low residual volatile content required
Name
Model
|
100
|
350
|
500
|
750
|
1000
|
1500
|
2000
|
3500
|
4500
|
5000
|
|||
Tank Inner Volume (L)
|
100
|
350
|
500
|
750
|
1000
|
15000
|
2000
|
3500
|
4500
|
5000
|
|||
Maximum charging capacity (L)
|
40
|
140
|
200
|
300
|
400
|
600
|
800
|
1400
|
1800
|
2000
|
|||
Maximum charging weight (kg)
|
20
|
70
|
100
|
150
|
200
|
300
|
400
|
700
|
900
|
1000
|
|||
Rotational speed (RPM)
|
3~13
|
6
|
5
|
4
|
4
|
4
|
|||||||
Motor Power K W)
|
0.75
|
1.1
|
1.5
|
2.2
|
3
|
4
|
5.5
|
7.5
|
11
|
15
|
|||
Floor space (mm)
|
2160
X800
|
2160
X800
|
2350
X800
|
2560
x1000
|
2860x
1300
|
3060
x1300
|
3260
x1400
|
3760
x1800
|
3960
X200
|
4400
x2500
|
|||
Swivel height (mm)
|
1750
|
2100
|
2250
|
2490
|
2800
|
2940
|
2990
|
3490
|
4100
|
4200
|
|||
In-tank design pressure (MPa)
|
-0.1~0.15
|
||||||||||||
Jacket design Pressure (MPa)
|
≤0.3
|
||||||||||||
Weight (kg)
|
800
|
1100
|
1200
|
1500
|
2800
|
3300
|
3600
|
6400
|
7500
|
8600
|
Note: to dry before and after a large volume changes in the material, the loading coefficient can be suitably increased or reduced, the maximum charge volume can not contact the bottom surface of the vacuum tube.
The motor can be adjusted according to user requirements, speed of 0~6rpm, the above technical parameters of the proportion of the material according to 0.6g/c M3 calculation, such as exceeding, the order should be put forward; if the user needs pressure vessel certificate, the order should be put forward; if the liner material is made of glass-lined, the order should be made Materials such as flammable and explosive, the order must be clearly put forward, otherwise strictly prohibited to use.
The scene pictures